Chrysler/Mercedes NAG1, 722.6, W5A580, WA580, W5A380, W5J400, Deep PML Transmission Pan

Finish *
Current stock: 0


All orders include: transmission pan, mounting bolts, and magnetic drain plug. A PML gasket is included - stock gaskets will not work with this PML pan.

Volume: 1 1/2 to 2 quarts over stock

Dimensions: About 3.5 inches tall, 1.8 taller than stock. Click image below for larger image.


Number of Bolts: 6

Applications for This PML Transmission Pan

Many Chrysler, Dodge, Jeep, and Mercedes vehicles have the NAG1, 722.6 (W5A580, WA580, W5A380, W5J400) transmission so PML has designed three different pans for the transmission.

Some vehicles which typically can use this pan are:

  • Jeep Grand Cherokee (SRT8, Laredo, Limited, Overland), 2006 to 2013
  • Dodge Magnum, Charger, Challenger, 2006 to 2013
  • Chrysler 300, 300C with 5 speed transmissions, 2005 to 2012
  • Mercedes (several models/years, sound plate may need altering, see Installations below)

Always check your vehicle to verify transmission and clearance as configurations vary. Scroll down to the Installations section at the bottom of this page for pictures of vehicles with this transmisson pan.

This pan is available in three finishes. 


  • Cooling — extra capacity, fins, and aluminum construction for reported temperature drops of 10 to 30 degrees
  • Clearance — step to clear frame
  • Drain — on the side for safety, pan includes magnetic drain plug and mounting bolts
  • Secure seal — machined flat flange, no more retaining clips and formed gasket
  • Strength — high quality, thick walls

PML makes three pans for the NAG1/722.6 transmission. Need help figuring out which pan you need? Check out this video or see our NAG1/722.6 Transmission Guide for help. 



PML's pan is not compatible with the stock gasket. PML's gasket is not compatible with the stock pan.A PML cork and rubber gasket is included (normally $18) for those who prefer a gasket over RTV.  

In this video, learn how this PML pan seals to the transmission housing:

Filter for PML 722.6/NAG1 Transmission Pan

PML design this pan to work with the stock filter. The Mercedes part number on the filter PML used during design and development is 140 277 00 95. There are filter supports cast into the pan to hold the filter in place at the same level as the stock pan. The filter supports eliminate the need for an extension.

Dipstick and Transmission Fluid Level

The fluid level should be at the same level in the stock pan and a PML pan. On many vehicles, the dipstick uses the bottom of the pan as a stop. PML pans have a ledge where the dipstick hits at the same level as the stock pan even though the PML pan is larger overall. In the above images of the inside of the pan, you can see the square ledge near the filter supports.

Many vehicles with these transmissions do not have a dipstick and the correct fluid level is based on temperature. The cap for the transmission fluid fill and level check can say "See Dealer". The installer of a replacement pan needs to have the correct tools to replace the transmission fluid according to the factory instructions. PML does not provide a dipstick.

PML Transmission Pan Features

  • Increased oil capacity for cooler temperatures
  • Sand-cast aluminum with raised fins
  • 3/16-inch thick wall construction to add strength to the transmission case
  • 3/8-inch thick gasket flange will not bend when bolts are tightened
  • Machined gasket surface for a secure seal
  • Boss cast into pan can be machined for a temperature sensor
  • Drain hole and magnetic drain plug for easier, less messy maintenance

All PML transmission pans ship with new mounting bolts and a magnetic drain plug.

Additional Info

Additional Info